Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
How do you really feel in regards to A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't precisely brain surgery, yet it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging project. If the old bathtub is readily accessible, the project can move quickly; if you have to open a wall to eliminate the old tub as well as position the new tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Instead of hiring a professional to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you might require a professional plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a new tub and also do not need to change the arrangement of your previous water pipelines.
Your devices and material list must make up the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to stop stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is disconnect the supply of water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly come from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet as well as the typical electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bath and the tiling, bring about difficulties with moisture and possible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our piece on Installing A Bathtub. Thanks a lot for taking time to browse our content. Are you aware of another person who is fascinated by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Do not hesitate to promote it. Thanks so much for going through it.
Call
Report this page